Page History

password

password

Specifies the password to use to log in to the SMSC.

systemType

cp

This parameter is used to categorize the type of ESME (External Short Message Entity) that is binding to the SMSC (max. 13 characters).

dataCoding

0

Camel 2.11 Defines the data coding according the SMPP 3.4 specification, section 5.2.19. (Prior to Camel 2.9, this option is also supported.) Example data encodings are:
0: SMSC Default Alphabet
3: Latin 1 (ISO-8859-1)
4: Octet unspecified (8-bit binary)
8: UCS2 (ISO/IEC-10646)
13: Extended Kanji JIS(X 0212-1990)

alphabet

0

Camel 2.5 Defines encoding of data according the SMPP 3.4 specification, section 5.2.19. This option is mapped to Alphabet.java and used to create the byte[] which is send to the SMSC. Example alphabets are:
0: SMSC Default Alphabet
4: 8 bit Alphabet
8: UCS2 Alphabet

encoding

ISO-8859-1

only for SubmitSm, ReplaceSm and SubmitMulti Defines the encoding scheme of the short message user data.

enquireLinkTimer

5000

Defines the interval in milliseconds between the confidence checks. The confidence check is used to test the communication path between an ESME and an SMSC.

transactionTimer

10000

Defines the maximum period of inactivity allowed after a transaction, after which an SMPP entity may assume that the session is no longer active. This timer may be active on either communicating SMPP entity (i.e. SMSC or ESME).

initialReconnectDelay

5000

Defines the initial delay in milliseconds after the consumer/producer tries to reconnect to the SMSC, after the connection was lost.

reconnectDelay

5000

Defines the interval in milliseconds between the reconnect attempts, if the connection to the SMSC was lost and the previous was not succeed.

registeredDelivery

1

only for SubmitSm, ReplaceSm, SubmitMulti and DataSm Is used to request an SMSC delivery receipt and/or SME originated acknowledgements. The following values are defined:
0: No SMSC delivery receipt requested.
1: SMSC delivery receipt requested where final delivery outcome is success or failure.
2: SMSC delivery receipt requested where the final delivery outcome is delivery failure.

serviceType

CMT

The service type parameter can be used to indicate the SMS Application service associated with the message. The following generic service_types are defined:
CMT: Cellular Messaging
CPT: Cellular Paging
VMN: Voice Mail Notification
VMA: Voice Mail Alerting
WAP: Wireless Application Protocol
USSD: Unstructured Supplementary Services Data

sourceAddr

1616

Defines the address of SME (Short Message Entity) which originated this message.

destAddr

1717

only for SubmitSm, SubmitMulti, CancelSm and DataSm Defines the destination SME address. For mobile terminated messages, this is the directory number of the recipient MS.

sourceAddrTon

0

Defines the type of number (TON) to be used in the SME originator address parameters. The following TON values are defined:
0: Unknown
1: International
2: National
3: Network Specific
4: Subscriber Number
5: Alphanumeric
6: Abbreviated

destAddrTon

0

only for SubmitSm, SubmitMulti, CancelSm and DataSm Defines the type of number (TON) to be used in the SME destination address parameters. Same as the sourceAddrTon values defined above.

sourceAddrNpi

0

Defines the numeric plan indicator (NPI) to be used in the SME originator address parameters. The following NPI values are defined:
0: Unknown
1: ISDN (E163/E164)
2: Data (X.121)
3: Telex (F.69)
6: Land Mobile (E.212)
8: National
9: Private
10: ERMES
13: Internet (IP)
18: WAP Client Id (to be defined by WAP Forum)

destAddrNpi

0

only for SubmitSm, SubmitMulti, CancelSm and DataSm Defines the numeric plan indicator (NPI) to be used in the SME destination address parameters. Same as the sourceAddrNpi values defined above.

priorityFlag

1

only for SubmitSm and SubmitMulti Allows the originating SME to assign a priority level to the short message. Four Priority Levels are supported:
0: Level 0 (lowest) priority
1: Level 1 priority
2: Level 2 priority
3: Level 3 (highest) priority

replaceIfPresentFlag

0

only for SubmitSm and SubmitMulti Used to request the SMSC to replace a previously submitted message, that is still pending delivery. The SMSC will replace an existing message provided that the source address, destination address and service type match the same fields in the new message. The following replace if present flag values are defined:
0: Don't replace
1: Replace

typeOfNumber

0

Defines the type of number (TON) to be used in the SME. Use the sourceAddrTon values defined above.

numberingPlanIndicator

0

Defines the numeric plan indicator (NPI) to be used in the SME. Use the sourceAddrNpi values defined above.

lazySessionCreation

false

Camel 2.8 onwards Sessions can be lazily created to avoid exceptions, if the SMSC is not available when the Camel producer is started.
Camel 2.11 onwards Camel will check the in message headers 'CamelSmppSystemId' and 'CamelSmppPassword' of the first exchange. If they are present, Camel will use these data to connect to the SMSC.

httpProxyHost

null

Camel 2.9.1: If you need to tunnel SMPP through a HTTP proxy, set this attribute to the hostname or ip address of your HTTP proxy.

httpProxyPort

3128

Camel 2.9.1: If you need to tunnel SMPP through a HTTP proxy, set this attribute to the port of your HTTP proxy.

httpProxyUsername

null

Camel 2.9.1: If your HTTP proxy requires basic authentication, set this attribute to the username required for your HTTP proxy.

httpProxyPassword

null

Camel 2.9.1: If your HTTP proxy requires basic authentication, set this attribute to the password required for your HTTP proxy.

sessionStateListener

null

Camel 2.9.3: You can refer to a org.jsmpp.session.SessionStateListener in the Registry to receive callbacks when the session state changed.

addressRange

""

Camel 2.11: You can specify the address range for the SmppConsumer as defined in section 5.2.7 of the SMPP 3.4 specification. The SmppConsumer will receive messages only from SMSC's which target an address (MSISDN or IP address) within this range.